20′ Enclosed Race Trailer – Part 3 – Electrics & Winch

As previously discussed, the shore power connection wasn’t exactly high quality. Someone removed the 30 Amp plug and replaced it with a 15 Amp plug that didn’t actually fit in the housing. Since it was on the driver’s side, going down the road every time I looked in the mirror, that thing was flapping at me.

20190422_143515

Since everything had to come off the wall for paint, including the electrical panel, the was a fairly straight forward fix. A new 30A shore power connector was fitted, along with an adapter for use with normal 20A service.

20190501_143406_HDR
20190429_173645

With that fixed, it was a simple matter of relocating the wiring in a way that was tidier, and positioned in a better place (the plugs were too high on the wall originally, and the E Track too low, so they switched positions). I removed the plug along the front wall, as it seemed superflous. I may re-add that later, but I already have plenty of 120v plugs in the trailer now.

20190429_160019

With the 120v service sorted it, it was time to move to the 12v side of things. My main 12v goals are:
-A winch to load the car
-An electrical jack
-A battery to power all that (and eventually some interior lights)
-A solar panel to keep the battery charged

The main component here is the battery and battery box. A tongue tool box from HF was mounted at the front of the trailer.

20190427_145528_HDR

I didn’t realize when I bought it that it was narrower than the outer frame rails, but I figured it was cheap, and it was big enough to do what I needed, so while it might look weird, there’s no real reason to replace it at this point.

I was a little concerned with the front mount bolts chafing the wiring harness from the truck:

20190427_143152

I found that I didn’t have any wire loom big enough to wrap around all those cables, but I DID have loom big enough to fit around the bolt. Stupid? Stupid like a fox!

20190427_145517

The battery box was mounted around the center frame rail:

20190427_145540_HDR

I didn’t have much horizontal real-estate to mount the solar panel to, but when parked at home, the panel faces nearly due west, and is in full sun in the afternoon.

20190430_155156_HDR

I was a bit concerned it wouldn’t work well like that (since all directions are to mount it horizontally), but it appears to be putting out plenty of juice:

20190430_153513

The battery never sees that much power, thankfully, as the solar panel runs through a 12v charge controller to prevent over charging the battery.

I drilled a few holes through the frame with big rubber grommets for the 12v wires to pass from the battery to inside the trailer under the floor, with marine cable pass-throughs to keep the weather and bugs out.

20190430_180056_HDR

I mounted the winch using a Bulldog winch mount. The front 2 bolts are through the frame, the rear 2 are bolted through a 6 x 8″, 3/8″ thick spreader plate.

20190501_140901

The winch wiring runs to the solenoid / wireless control box, and then to a 12v fuse block to provide service for lights and other sundries, then to the battery via a 150A circuit breaker.

20190501_134001
20190501_133243_HDR

It’s definitely not a professional job (because I’m definitely not a professional), but it’s about probably the tidiest I could do without shortening the winch power cables. That’ll probably happen eventually, but I want to wait for a few months and make sure nothing crops up as a reason to move something drastically.

The electrics are *DONE*. FINALLY. Between drilling holes for grommets through the frame, making cables and figuring out where I want everything mounted, and cleaning up the 120v wiring, it took all my free time for about 3 days.

Oh! Wait…I’m sick or walking all the way to the shop for fresh tool batteries. I’ve got an idea!

20190501_144439

Yeah that’ll work. I think that lives there now.

Continued in Part 4